Everest MR Series
Everest
KBT
Everest
KBS
3-4 yard Everest
Dump
|
Specs for
Everest 3-4 yd. Dump
KBLH 86" Wide Body
& KBLHX 92" Wide Body
Capacities From 1.8 Yds to 5.4 Yd Water Level
Length: Available in
7', 8', 9', and 10' Lengths
Construction: 10
Gauge Mild Steel, 6" Channel @ 8.20 lbs. Longsills, 3" @4.1 lbs. Channel
Cross-members on 16" Centers. Plate gussets at front of Longsills,
Full Width Rear Skirt 9" Deep with Side Skirts.
Floor: One Piece10 Gauge Floor with 45° Ramps to Each
Side. "Stacked" Structural Floor Supports. 3/16" Abrasion Resistant
Available.
Sides:
13", 19', and 25" heights available. One
Piece Plate with Boxed Section Toprail & Dirt Shedding Rub Rail Bottom |
|
3 - 4 Yd.
Everest with Rigid Front Mud Flaps
and Pintle Plate
|
Vertical Rear Post 9" by 4' Section
Two Lift Lugs per Side Standard
6" High Rear Board Pockets to Accept 2" Plank
Inner Front Board Pocket to Top of Headboard
6" High Outer Front Board Pocket
One Front Post 6" X 7/8" Section Standard
Side Posts Optional
|
Tailgate:
One Piece Skin Plate of same material as Floor
Perimeter Box Reinforcement
Lower Rubrail Material Shedding Design
Two-way Action, 1/4" Adjustment Chains, 1/2" Flame Cut Hinge ears with 1
- 1/4" Diameter galvanized Handle Pins
1 - 1/4" Diameter Lower Latch Rod
Two Cabin Hooks Per Side Attached to rear Post
1" Locking Handle
(Drivers-Side-Front)
Single Adjustable Push-Rod to Rear
1" Diameter Full Width Traverse Rod with 4 bearing Points
Positive Lock CAM Gives a "Double" Lock
Rear Latches Independently Adjustable
Flame Cut 1/2" Latch Ears with 5/8" Flame Cut Lock Finger
|
|
|
Everest 3 - 4 yd Dump with
Single Coal Chute, Pintle Plate with ball Hitch, JobBox Under Body Boxes, and
Donovan Canvas Roller
Click on photo for a larger image.
Close window to return to this page.
|
Cab Shield:
36'
High headboard of 10 gauge Steel, 2 horizontal Vee Pleats, 12" Cab Shield.
Hoist Frame:
Hoist
& Hoist frame Selected to Meet Application.
|
Everest MR Series |
MR 10 Yd Dump
Body with Everest Telescopic Hoist
& Three Coal Chutes in the Double Acting Tailgate |
10 to 24 Yard
Capacities
Ideal for Contractors, Municipalities, Asphalt Paving and Other
Applications
Length: Available
from 12 to 18 feet.
Understructure:
Formed U--Shape sills provide a wide & continuous floor support and carry
exhaust heat to the rubrails.
Formed Cross-members provide maximum front & rear floor support & carry
exhaust heat to the sills & rubrails.
Floor: One Piece Floor Formed From Ultra High Strength
(100,000 p.s.i.) 1/4" AR Steel Plate
Sides:
Formed from 3/16" HT Steel Plate.
Dirt Shedding Rubrails.
Formed Horizontal Reinforcing Plates.
Fully Boxed Toprails.
Wide Faced Vertical Side Posts and Front Posts provide Tough Side Support.
Tailgate:
|
 |
Double Acting Tailgate, Slanted for Maximum Load Discharge Clearance.
Standard Nine
Panel Bracing
Formed From 1/4" (100,000 PSI) AR Steel.
Hinges of 1/2" Flame Cut Steel Plate.
Front Plate:
Formed 3/16" Steel Reinforced with Vertical Pleats.
10" Deep Cylinder Doghouse Provides Easy Access to the EVEREST Telescopic
Cylinder.
Cab Shield: Standard Everest Cabshield can Be Fitted to the
Monoshell Dump Body.
Weight: Up to 40% Lighter than Conventional Cross-member Bodies
of Comparable Strength when Combined with Everest telescopic Hoist. |
Specs for
Everest KBT Dump Bodies10 to 24 Yard
Capacities
Heavy Duty "D" Series Design for Contractors &
Municipalities |
Length:
Understructure:
6" I-Beam Long Sills
4" I-Beam Cross-members on 12" Centers
Tubular Laced Understructure Available for Total Floor Support.
Sides:
Formed Vertical 8" Face Side and Front Posts
Full Depth Formed Tailgate Posts.
Boxed Toprail
Boxed Front Posts
Sideboard Pockets
Dirt Shedding Rubrails.
Tailgate:
Heavy Duty Double Acting Slanted tailgate
Boxed 9 Panel Bracing
Heavy Duty hardware & Latching Mechanism.
Dual Chain Sets & Retainers
Front Plate:
Double Pleated Reinforced Headboard
|
| Specs for
Everest KBS Dump Bodies 4 to 8 Yard
Capacities
Heavy Duty Design for Contractors & Municipalities |
Everest KBS Dump Body |
Construction:
Body Plate & Bracing of HT Steel
Body Plates all One Piece - no Splicing
All Body Shell welds are Continuous Welds
Sides, Front & Floor of 3/16" Steel
Understructure:
6" I-Beam Long Sills
4" I-Beam Cross-members on 12" Centers
Sides:
Formed Vertical 8" Face Side and Front Posts
Full Depth Formed Tailgate Posts.
Boxed Toprail
Boxed Front Posts
Sideboard Pockets
Dirt Shedding Rubrails.
Tailgate:
Heavy Duty Double Acting Tailgate
Boxed 6 Panel Bracing
Heavy Duty Hardware & Latching Mechanism.
Heavy Duty Chain Sets & Retainers.
Front Plate:
Double Pleated reinforced headboard. |
