Aquidneck Machine, Inc.
52 Aquidneck Drive
Tiverton, RI 02878
(401) 625-5664
Fax: (401) 625-1948

Quality Truck Bodies and Truck Equipment

              Everest Dump Bodies:  "Quality By Design"

Heavy Duty Dump Bodies in All Sizes to Meet All Needs

Everest KBLH Series: 3-4 yard capacity

 Everest MR Series: 10 - 24 yard capacity

    Everest KBT: 10 - 24 yard capacity

    Everest KBS: 4- 8 yard capacity

 A rugged dump whether you are looking for a small dump or a large dump. Top quality. All sizes.

 
3-4 yard Everest Dump

Specs for Everest 3-4 yd. Dump Body

KBLH 86" Wide Body & KBLHX 92" Wide  Body
Capacities From 1.8  Yds to 5.4 Yd Water Level

Length:  Available in 7', 8', 9', and 10' Lengths

Construction:  10 Gauge Mild Steel, 6" Channel @ 8.20 lbs. Longsills, 3" @4.1 lbs. Channel Cross-members on 16" Centers. Plate gussets at front of Longsills, Full Width Rear Skirt 9" Deep with Side Skirts.
  
   
Floor: One Piece10 Gauge Floor with 45° Ramps to Each Side. "Stacked" Structural Floor Supports. 3/16" Abrasion Resistant Available.
  
    
Sides:    13", 19', and 25" heights available. One Piece Plate with Boxed Section Toprail & Dirt Shedding Rub Rail Bottom
 

Vertical Rear Post 9" by 4' Section
Two Lift Lugs per Side Standard

3 - 4 Yd. Everest with Rigid Front Mud Flaps
and Pintle Plate
    

Everest 3 - 4 yd Dump with Single Coal Chute, Pintle Plate with ball Hitch, JobBox Under Body Boxes, and Donovan Canvas Roller
    

Click on photo for  a larger image.  
Close window to return to this page.

6" High Rear Board Pockets to Accept 2" Plank
Inner Front Board Pocket to Top of Headboard
6" High Outer Front Board Pocket
One Front Post 6" X 7/8" Section Standard
Side Posts Optional

Tailgate: One Piece Skin Plate of same material as Floor Perimeter Box Reinforcement Lower Rubrail Material Shedding Design Two-way Action, 1/4" Adjustment Chains, 1/2" Flame Cut Hinge ears with 1 - 1/4" Diameter galvanized Handle Pins 1 - 1/4" Diameter Lower Latch Rod Two Cabin Hooks Per Side Attached to rear Post 1" Locking Handle (Drivers-Side-Front) Single Adjustable Push-Rod to Rear 1" Diameter Full Width Traverse Rod with 4 bearing Points Positive Lock CAM Gives a "Double" Lock Rear Latches Independently Adjustable Flame Cut 1/2" Latch Ears with 5/8" Flame Cut Lock Finger

Cab Shield:  36' High headboard of 10 gauge Steel, 2 horizontal Vee Pleats, 12" Cab Shield.

Hoist Frame:  Hoist & Hoist frame Selected to Meet Application.

10 to 24 Yard Capacities
Ideal for Contractors, Municipalities, Asphalt Paving  and Other Applications

Length:  Available from 12 to 18 feet.

Understructure: 
Formed U--Shape sills provide a wide & continuous floor support and carry exhaust heat to the rubrails.
Formed Cross-members provide maximum front & rear floor support & carry exhaust heat to the sills & rubrails.

Floor: One Piece Floor Formed From Ultra High Strength (100,000 p.s.i.) 1/4" AR Steel Plate

Sides: 
Formed from 3/16" HT Steel Plate. 
Dirt Shedding Rubrails.
Formed Horizontal Reinforcing Plates.
Fully Boxed Toprails.
Wide Faced Vertical Side Posts and Front Posts provide Tough Side Support.

Tailgate:

Double Acting Tailgate, Slanted for Maximum Load Discharge Clearance.
Standard Nine Panel Bracing
Formed From 1/4" (100,000 PSI) AR Steel.
Hinges of 1/2" Flame Cut Steel Plate.

Front Plate:
Formed 3/16" Steel Reinforced with Vertical Pleats.
10" Deep Cylinder Doghouse Provides Easy Access to the EVEREST Telescopic Cylinder.

Cab Shield: Standard Everest Cabshield can Be Fitted to the Monoshell Dump Body.

Weight:  Up to 40% Lighter than Conventional Cross-member Bodies of Comparable Strength when Combined with Everest telescopic Hoist.

10 to 24 Yard Capacities
Heavy Duty "D" Series Design for Contractors & Municipalities

Length: 

Understructure: 
6" I-Beam Long Sills
4" I-Beam Cross-members on 12" Centers
Tubular Laced Understructure Available for Total Floor Support.

Sides: 
Formed Vertical 8" Face Side and Front Posts
Full Depth Formed Tailgate Posts.
Boxed Toprail
Boxed Front Posts
Sideboard Pockets
Dirt Shedding Rubrails.

Tailgate:
Heavy Duty Double Acting Slanted tailgate
Boxed 9 Panel Bracing
Heavy Duty hardware & Latching Mechanism.
Dual Chain Sets & Retainers

Front Plate:
Double Pleated Reinforced Headboard
   

4 to 8 Yard Capacities
Heavy Duty Design for Contractors & Municipalities

Construction:
Body Plate & Bracing of HT Steel
Body Plates all One Piece - no Splicing
All Body Shell welds are Continuous Welds
Sides, Front & Floor of 3/16" Steel

Understructure: 
6" I-Beam Long Sills
4" I-Beam Cross-members on 12" Centers

Sides: 
Formed Vertical 8" Face Side and Front Posts
Full Depth Formed Tailgate Posts.
Boxed Toprail
Boxed Front Posts
Sideboard Pockets
Dirt Shedding Rubrails.

Tailgate:
Heavy Duty Double Acting Tailgate
Boxed 6 Panel Bracing
Heavy Duty Hardware & Latching Mechanism.
Heavy Duty Chain Sets & Retainers.

Front Plate:
Double Pleated reinforced headboard.